بناوینی راکتۆری پاشەکەوتی

Shunt Reactor dikevîne reaktîfî kapaîtîva ya rêzikî derêngîn de peyda kirin. Shunt Reactorek constrûkasyonan ji alîkar bê alîkar vekirin, lê bîyanên pêşpeyê yê constrûkasyonê çend saz bihêri.

Shunt Reactorek Core

Gapped Core li sererastî di shunt reactor de bikar înin. Core hatine jî yên Cold Rolled Grain Oriented Silicon Steel sheet bikin da hysteresis lossesê bigihînin. Yân sheetan laminated ne ku eddy current lossesê bigihînin. Gaps di constrûkasyonda xwestin da spacers of high modulus of electricity di navên laminations de bihêrin. Li sererastî, gaps radîyal bimînin. Laminations di her packet de li sererastî longitudinal bimînin. Li sererastî, 5 limb 3 phase structure of core bikar înin. Ev shell type construction e. Yokes and side limbs nayê gapped be, lê three inner limbs for individual phase di radîyal gaps de dibikin.

Shunt Reactorek Winding

Li sererastî, winding of a reactor yek wate ne. Ev çend saz di copper conductors de ye. Conductors paper insulated ne. Insulated spacers di navên turns de bihêrin da path for oil circulation bimînin. Ev arrangement efficient cooling of the windingê bigihînin.

Reactor Cooling System

Li sererastî, shunt reactor di low current de xebitîn, buna ONAN (Oil Natural Air Natural) cooling pişaz li sererastî, heta ji bo extra high voltage ratings. Radiator bank bi main tank hatiye hevkirin da faster cooling bimînin.

Reactor Tank

Main tank of larger rated reactor for UHV and EHV system li sererastî bell tank type e. Ji bo bottom tank and bell tank steel sheet of suitable thickness bikar înin. Steel sheets of suitable pieces welded together to form both of the tanks. Tanks designed and constructed to withstand full vacuum and positive pressure of one atmosphere. Tanks should be so designed that these can be transported by road and railways.

Reactor Conservator

Conservator provided at the top of the tank with main tank to conservator connecting pipe line of suitable diameter. Conservator generally horizontally aligned cylindrical tank, to provide adequate space to the oil for expansion due to temperature rise. Flexible separator between air and oil or air cell provided in the conservator for the said purpose. Conservator tank also equipped with a magnetic oil gauge to monitor the oil level in the reactor. Magnetic oil gauge also gives an alarm through a normally open (NO) DC contact, attached to it when oil level falls below a preset level due to oil leakage or any other reason.

Pressure Relief Device

Due to huge fault inside the reactor there may be sudden and excessive expansion of oil inside the tank. This huge oil pressure generated in the reactor should be released immediately along with separation of the reactor from the live power system. Pressure Relief Device does the job. This is a spring loaded mechanical device. This is fitted on the roof of the main tank. At the event of actuation, the upward pressure of the oil in tank becomes greater than the downward spring pressure, as a result there will be an opening in the valve disc of the device through which the expanded oil comes out to relief the pressure formed inside the tank. There is a mechanical lever attached to the device which is normally in horizontal position. When the device is actuated, this lever becomes vertical. By observing the alignment of the lever even from ground level one can predict whether the Pressure Relief Device (PRD) has been operated or not. The PRD is accompanied with a trip contact to trip the shunt reactor at the event of actuation of the device.
N B: – PRD or such type of device cannot be reset from remote once it actuated. It can only be reset manually by moving the lever to its original horizontal position.

Buchholz Relay

One Buchholz relay fitted across the pipe connecting the conservator tank and main tank. This device collects gases generated in the oil and actuates the alarm contact attached to it. It has also a trip contact which is actuated at the event of sudden accumulation of gas in the device or rapid flow of oil (oil surge) through the device.

Silica Gel Breather

When oil becomes hot, it is expanded thus air from conservator or air shell (where air shell is used) comes out. But during contraction oil, air from the atmosphere enters into conservator or air shell (where air shell is used). This process is called breathing of the oil immersed equipment (like transformer or reactor). During breathing, obviously moisture can enter into the equipment if it is not taken care of. An pipe from conservator tank or air shell is fitted with a container filled with silica gel crystal. When air is passed through it, the moisture is absorbed by the silica gel.

Winding Temperature Indicator

Winding temperature indicator is a kind of indicating meter associated with a relay. This consists of a sensor bulb placed in an oil filled pocket on the roof of reactor tank. There are two capillary tubes between sensor bulb and the instrument housing. One capillary tube is connected to the measuring bellow of the instrument. Other capillary tube connected to the compensating bellow fitted in the instrument. The measuring system, i.e. sensor bulb, both capillary tubes and both bellows are filled with a liquid which changes its volume when temperature changes. The pocket in which the sensor bulb is immersed, is surrounded by a heating coil which is fed by a current proportional to the current flowing through the winding of reactor. Gravity operated NO contacts are attached to the pointer system of the instrument to provider high temperature alarm and trip respectively.

Oil Temperature Indicator

Oil temperature indicator consists of a sensor bulb placed in an oil filled pocket on the roof of reactor tank. There are two capillary tubes between sensor bulb and the instrument housing. One capillary tube is connected to the measuring bellow of the instrument. Other capillary tube connected to the compensating bellow fitted in the instrument. The measuring system, i.e. sensor bulb, both capillary tubes and both bellows are filled with a liquid which changes its volume when temperature changes. The pocket in which the sensor bulb is immersed, is fitted at the location of hottest oil.

Bushing

The winding terminals of each phase comes out from the reactor boy through an insulated bushing arrangement. In high voltage shunt reactor, the bushings are oil filled. The oil is sealed inside the bushing that means there is no link between the oil inside the bushing and oil inside the main tank. Oil level gauge is provided on the expansion chamber of the condenser bushings.

Statement: Respect the original, good articles worth sharing, if there is infringement please contact delete.