Transformer sa ferroalloy (distribution transformer)

Ang amihanan nga kompanya nagpursige sa pagtumon sa sumusunod nga apat ka mga layunin sa pagbuhat ug pag-manufacture sa mga transformer:

• Ang mga transformer mismo adunay maayo nga mga katangian sa pag-save sa energy: no-load loss, no-load current, ug load loss. Pahibaloan ang impedance voltage percentage ngadto sa pinakabag-o, pili og angkop nga impedance voltage percentage sa kasagaran nga capacity, gamit ang may kalidad nga raw materials, ug gamit ang advanced technologies sama sa small oil gaps aron mabuhat ang transformer nga tunay nga energy-saving, nga adunay performance level sa mid-1990s sa internationally developed country products.

• Ang mga transformer adunay kaestabihan ug mahimong matagal nga serbisyo. Ang design technology sa bag-ong structure products kinahanglan naa sa operational testing ug type testing verification, nga adunay design life nga dili mas baba sa trenta ka tuig.

• Kinahanglan ang usa ka overload capacity aron siguradohon nga tanang operational indicators molabay sa national standard requirements kung ang users mobagsak sa rated capacity sa 20%.

•  Bawasan ang maintenance workload sa users, i-prevent sila sa pag-hang sa cores sa long-term use, ug design ang free maintenance time nga dili mas baba sa sampel ka tuig. Ang free maintenance period duol sa dwenta ka tuig.

Paghimo ug pagpili sa mga materyales, structures, ug processes sa transformer:

　　Ang kompleto nga ferroalloy furnace transformer mainhong nahimong walo ka bahin:

　　Namely: iron core, winding, body, oil tank, final assembly, accessories. Below are the separate introductions、

• Iron core: Sa mga materyales, natapos nato ang BaoWu Steel's 30Q130 o Nippon Steel's 30Z130 silicon steel sheet, nga basic consistent sa mga materyales nga gigamit sa internationally developed countries.

• Ang structure adopts a fully inclined seam plate type, ug ang koneksyon sa upper ug lower clamps adopts a low magnetic steel plate pull plate structure, changing the previous square iron structure to ensure that there are no holes or defects on the iron chip, the magnetic flux density of each section of the iron core is consistent, and there is no distortion. In the shear process, German imported Georg shear lines are used to control the shear burrs to be less than 0.02mm (standard<0.05mm is qualified), and the length tolerance per meter is less than 0.02mm, thereby increasing the lamination coefficient and reducing the gap between the seams, It avoids local overheating of the iron core, reduces product noise, no-load loss, and no-load current.

• Winding: Oxygen free copper electromagnetic wire is used from the material, mainly controlling its ρ 20 ℃<0.017241, in addition, the main control is the material and tightness of the paper wrapped insulation, while other insulation materials have been greatly improved. The main purpose is to make the coil have good axial and radial stability as much as possible, and to improve its overload capacity and thermal stability. The loss has also decreased.

• Body: All wooden components of the body have been changed to laminated wood, improving the stiffness of the lead frame. The upper and lower pressing plates are made of cardboard or epoxy resin molded parts, which increases the insulation distance between the electrical conductor and the ground compared to iron pressing plates and can reduce the size of the "window height". 1、 The secondary main insulation adopts imported cardboard, which increases the strength of the main insulation. The multi coil adopts an overall package, which improves the reliability of the product. The drying of the device body adopts Norwegian vapor phase drying equipment, which is thorough and does not damage the insulation, and has the function of flushing the device body.

•  Fuel tank: The fuel tank adopts a folded plate type. Minimize welding seams as much as possible, increase strength, and conduct positive and negative pressure tests to ensure the reliability of product sealing.

• General assembly: After the body is dry, the winding loosens and is compressed with hydraulic equipment, achieving good results. Vacuum oil injection is used to reduce air bubbles in the product winding, reduce partial discharge, and increase product life. Using new anti-aging sealing materials, the original leakage problem can be improved.

• Attachment: The main accessory water cooler is YS1 type oil water cooler, which is equipped with a descaling device instead of water quality. It can be installed separately or directly fixed on the transformer host (which can reduce installation work and floor space). The cooler is equipped with a control box, oil and water flow relays, and oil water pressure differential relays. The on load tap changer adopts domestic switches and is equipped with remote gear display.

　　The transformer oil is naphthenic anti-aging transformer oil produced in Karamay, and the oil protection is fully enclosed structure (that is, the pressure relief valve is equipped with diaphragm oil conservator structure)

About Transformer Maintenance：

        It is necessary to use the suspended core after the product arrives for long-distance transportation, mainly to solve the problems of loose fasteners during transportation and user acceptance of the manufacturer's products. However, regarding routine major repairs, we believe that it is necessary to inspect and replace those mechanical wear parts according to the original major repair cycle. For operating components such as pumps, it is not necessary to suspend the core inside relatively stationary transformers for a long time. Only monitoring the quality changes of oil such as gas chromatography is sufficient to grasp the condition of the transformer body, thereby saving maintenance costs and reducing the pollution of the transformer body and oil caused by suspended cores.

Pangitaan ang imong supplier

Vziman

Zhejiang Vziman Electric Group Co., Ltd. 3yrs + staff 10000+m² US$150000000 + China

Zhejiang Vziman Electric Group Co., Ltd.

3yrs + staff 10000+m² US$150000000 + China