Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

Distribution Lines: A Key Component of Power SystemsDistribution lines are a major component of power systems. On the same voltage-level busbar, multiple distribution lines (for input or output) are connected, each with numerous branches arranged radially and linked to distribution transformers. After being stepped down to low voltage by these transformers, electricity is supplied to a wide range of end users. In such distribution networks, faults such as phase-to-phase short circuits, overcurre

Analysis and Handling of DC System Grounding Faults in SubstationsWhen a DC system grounding fault occurs, it can be classified as single-point grounding, multi-point grounding, loop grounding, or reduced insulation. Single-point grounding is further divided into positive-pole and negative-pole grounding. Positive-pole grounding may cause misoperation of protection and automatic devices, while negative-pole grounding may lead to failure to operate (e.g., relay protection or tripping devices). On

In power circuits, voltage transformers (VTs) are often damaged or burned out. If the root cause is not identified and only the transformer is replaced, the new unit may quickly fail again, disrupting power supply to users. Therefore, the following checks should be performed to determine the cause of VT failure: If the voltage transformer has ruptured and oil residue is found on the silicon steel laminations, the damage was likely caused by ferroresonance. This occurs when unbalanced voltages or

With the rapid development of China's economy, the power industry has also gradually expanded in scale, increasing the requirements for both the installed capacity and the single-unit capacity of power transformers. This article provides a brief introduction to four aspects: transformer construction, transformer lightning protection, transformer faults, and transformer noise.A transformer is a commonly used electrical device capable of converting AC electrical energy. It can transform one form o

Optimized Guide to Transformer Fault Diagnosis and Advanced Testing TechniquesTransformers are core components in power systems, and their operational reliability directly impacts power supply safety. Common types include oil-immersed and dry-type transformers. Failures typically occur in the windings, core, connections, and insulation oil, with typical issues such as inter-turn short circuits, insulation aging, overheated joints, and multi-point core grounding.1. Common Fault IndicatorsImmediat

Fault Analysis and Troubleshooting of High-Voltage Vacuum Circuit BreakersIntroduction: Advantages and EvolutionHigh-voltage vacuum circuit breakers (VCBs) offer significant advantages over traditional oil or SF₆-based breakers, including: Oil-free and environmentally friendly design High dielectric strength in vacuum Excellent arc-quenching capability Long electrical and mechanical life Compact size, light weight Suitable for frequent operation Fire-resistant and low maintenanceThese benefits h

High-voltage switchgear is a critical electrical device in power systems. Deterioration in switchgear operating conditions is one of the main causes of power system failures. So, what are the common faults in high-voltage switchgear?I.Classification of High-Voltage Switchgear(1) Outdoor and Indoor TypesBased on installation location, high-voltage switchgear can be classified as outdoor or indoor types. Indoor switchgear is commonly used for systems at 10 kV and below. According to primary circui

Normal operating sound of a transformer. Although a transformer is static equipment, a slight, continuous "humming" sound can be heard during operation. This sound is an inherent characteristic of operating electrical equipment, commonly known as "noise." A uniform and continuous sound is considered normal; an uneven or intermittent noise is abnormal. Tools such as a stethoscope rod can assist in determining whether the transformer's sound is normal. The causes of this noise are as follows: Vibr

I. Common Fault Types and Diagnostic MethodsElectrical Faults Circuit Breaker Failure to Operate or Maloperation: Check the energy storage mechanism, closing/tripping coils, auxiliary switches, and secondary circuits. High-Voltage Fuse Blown: Measure voltage across the fuse terminals; inspect busbar joints, cable terminations, and protection relay settings. Busbar Discharge or Insulator Damage: Listen for discharge sounds, check temperature at busbar connections, and visually inspect insulators

With the continuous advancement of mechanization in modern society, the demand for electrical energy in daily life has significantly increased. To ensure that power supply meets this growing demand, the power system must operate with greater stability, safety, and real-time responsiveness. This highlights the critical importance of high-voltage disconnector switch quality during manufacturing.Manufacturers must strengthen their awareness of this responsibility to ensure reliable operation of hig