35kV Short-Circuit Current Limiter
Key attributes
| Brand | RW Energy |
| Model NO. | 35kV Short-Circuit Current Limiter |
| Rated voltage | 40.5kV |
| Rated normal current | 1250A |
| Series | DDX |
Product descriptions from the supplier
Product Introduction
The DDX1 Short-Circuit Current Limiter is a high-speed switch capable of interrupting short-circuit currents. It can break the short-circuit current within 10ms after a short-circuit fault occurs—well before the instantaneous value of the short-circuit current rises to its expected peak.Integrating fast cutting technology, high-voltage current limiting technology, electronic measurement and control technology, and high-voltage insulation technology, it enables rapid current limiting and interruption of short-circuit currents in power generation, distribution, and consumption systems. This protects key power equipment such as generators and transformers from the impact of catastrophic short-circuit currents.Meanwhile, it can also optimize the operation mode of the distribution system, achieving effects such as energy conservation and consumption reduction, improved power quality, and enhanced power supply reliability.
Product Features and Benefits
Strong short-circuit breaking capacity (large capacity), rated breaking short-circuit current of 50kA~200kA.
Fast breaking speed (high speed), the whole breaking time is less than 10ms.
The opening process has obvious current limiting characteristics (current limiting).
The action criterion uses the instantaneous value of current and the instantaneous value of current change rate.
The current sensor is integrated with a fast isolator for a simplified structure.
The electronic controller works independently in three phases through high temperature and strong interference tests to ensure the overall reliability of the product.
Electrical parameters
serial number |
Parameter Name |
unit |
Technical parameters |
|
1 |
Rated voltage |
kV |
40.5 |
|
2 |
Rated current |
A |
630-6300 |
|
3 |
Rated expected short-circuit breaking current |
kA |
50-200 |
|
4 |
Current limit coefficient = cut-off current / expected short-circuit current peak |
% |
15~50 |
|
5 |
Insulation level |
Power frequency withstand pressure |
kV/1min |
95 |
Lightning impact withstand pressure |
kV |
185 |
||
Product Applications
Related Products
Related Knowledges
-
Impact of DC Bias in Transformers at Renewable Energy Stations Near UHVDC Grounding ElectrodesImpact of DC Bias in Transformers at Renewable Energy Stations Near UHVDC Grounding ElectrodesWhen the grounding electrode of an Ultra-High-Voltage Direct Current (UHVDC) transmission system is located close to a renewable energy power station, the return current flowing through the earth can cause a rise in ground potential around the electrode area. This ground potential rise leads to a shift in the neutral-point potential of nearby power transformers, inducing DC bias (or DC offset) in their01/15/2026 -
HECI GCB for Generators – Fast SF6 Circuit Breaker1.Definition and Function1.1 Role of the Generator Circuit BreakerThe Generator Circuit Breaker (GCB) is a controllable disconnect point located between the generator and the step-up transformer, serving as an interface between the generator and the power grid. Its primary functions include isolating generator-side faults and enabling operational control during generator synchronization and grid connection. The operating principle of a GCB is not significantly different from that of a standard c01/06/2026 -
Distribution Equipment Transformer Testing, Inspection, and Maintenance1.Transformer Maintenance and Inspection Open the low-voltage (LV) circuit breaker of the transformer under maintenance, remove the control power fuse, and hang a “Do Not Close” warning sign on the switch handle. Open the high-voltage (HV) circuit breaker of the transformer under maintenance, close the grounding switch, fully discharge the transformer, lock the HV switchgear, and hang a “Do Not Close” warning sign on the switch handle. For dry-type transformer maintenance: first clean the porcel12/25/2025 -
How to Test Insulation Resistance of Distribution TransformersIn practical work, insulation resistance of distribution transformers is generally measured twice: the insulation resistance between thehigh-voltage (HV) windingand thelow-voltage (LV) winding plus the transformer tank, and the insulation resistance between theLV windingand theHV winding plus the transformer tank.If both measurements yield acceptable values, it indicates that the insulation among the HV winding, LV winding, and transformer tank is qualified. If either measurement fails, pairwise12/25/2025 -
Design Principles for Pole-Mounted Distribution TransformersDesign Principles for Pole-Mounted Distribution Transformers(1) Location and Layout PrinciplesPole-mounted transformer platforms should be located near the load center or close to critical loads, following the principle of “small capacity, multiple locations” to facilitate equipment replacement and maintenance. For residential power supply, three-phase transformers may be installed nearby based on current demand and future growth projections.(2) Capacity Selection for Three-Phase Pole-Mounted Tr12/25/2025 -
Transformer Noise Control Solutions for Different Installations1.Noise Mitigation for Ground-Level Independent Transformer RoomsMitigation Strategy:First, conduct a power-off inspection and maintenance of the transformer, including replacing aged insulating oil, checking and tightening all fasteners, and cleaning dust from the unit.Second, reinforce the transformer foundation or install vibration isolation devices—such as rubber pads or spring isolators—selected based on the severity of vibration.Finally, strengthen sound insulation at weak points of the ro12/25/2025
Related Solutions
-
Distribution automation systems solutionsWhat are the difficulties in overhead line operation and maintenance?Difficulty one:Overhead lines of distribution network have wide coverage,complicatedterrain,many radiation branches and distributed power supply,resultingin "many line faults and difficulty in fault troubleshooting".Difficulty Two:Manual troubleshooting is time-consuming and laborious.Meanwhile,therunning current,voltage and switching state of the line cannot be graspedin real time,because of the lack of intelligent technical m04/22/2025 -
RW8000 DMS Distribution Management System SolutionsOverviewNowadays, the development trend of power grid is intellectualization. As an important part of power grid, the power distribution system is very close to the customers and it has to run properly. The distribution management system (DMS）played an important role in it.Introduction:RW8000 power distribution management system (DMS) is designed for the smart grids. It is based on real-time application, centered on distribution network operation and management, focusing on the business process09/07/2023 -
High-Precision Electrical Parameter Monitoring System Solution1.IntroductionWith the increasingly stringent requirements for power supply quality in high-end facilities such as precision manufacturing, medical diagnosis, and data centers, traditional power monitoring systems, due to their low sampling accuracy and weak data analysis capabilities, can no longer meet the demand for deep insight and precise management of power quality. In response, we are introducing a new generation High-Precision Electrical Parameter Monitoring System. With millisecond-l09/28/2025
