Cogeneration | Comhchúiseoireacht Teas agus Fuinnimh
Cogeneration is also called as combined heat and power or combine heat and power. As it name indicates cogeneration works on concept of producing two different form of energy by using one single source of fuel. Out of these two forms one must be heat or thermal energy and other one is either electrical or mechanical energy.
Is é an chogeneration an modh is fearr, is ionsaithí, is glan agus is éifeachtaí chun comhtháthú a úsáid. D'fhéadfadh an t-úinéir bheith ina ghás nádúrtha, ola, diisel, propan, adhmaid, bassage, gual, nó rud eile. Oibríonn sé ar phrionsabal an-simplí, mar sin féin, úsáideann sé an t-úinéir chun cumhacht a chruthú agus úsáideann an t-eolraíocht seo chun teolaíocht a chruthú agus úsáideann an teolaíocht seo chun uisce a builleadh chun stíom a chruthú, do tháthú spáis agus fiú chun foirgnimh a chur go fuar.
In ionad pleanáil cumhachta traidisiúnta, tá an t-úinéir leagtha i bhbólair, ag tarlú airgeadra stíom ard-bhrú. Úsáideann an stíom ard-bhrú seo chun triobhán a dhreapadh, atá i dtreo a bhfuil alternóir ceangailte agus mar sin dreapann an alternóir chun cumhacht eolraíochta a chruthú.
Ansin cuireann an t-eolraíocht stíom go dtí an chondenser, áit a díoltas sí agus a dhéantar í a athrú chuig uisce agus mar sin tuairt sí siar go dtí an bholair chun níos mó cumhachta eolraíochta a chruthú. Is 35% amháin é an éifeachtachtacht den ionad cumhachta traidisiúnta seo. In cogeneration plant the low pressure steam coming from turbine is not condense to form water, instead of it its used for heating or cooling in building and factories, as this low pressure steam from turbine has high thermal energy.
Tá éifeachtachtacht an-chruinn ag cogeneration plant thart ar 80 – 90%. In India, the potential of power generation from cogeneration plant is more than 20,000 MW. The first commercial cogeneration plant was built and designed by Thomas Edison in New York in year 1882.
Mar a léirítear sa diagram uafásach, i gcumhacht pleanála traidisiúnta, nuair a thugaimid an t-úinéir mar ionchur, faightear cumhacht eolraíochta agus caillte agus mar thoradh ach i gcás cogaonú leis an t-úinéir mar ionchur, is é an toradh cumhacht eolraíochta, teolaíocht nó teolaíocht agus caillte.
In convential power plant, with 100 % energy input ,only 45 % of energy is used and rest 55 % is wasted but with cogeneration, the total energy used is 80% and energy wasted is only 20%. It means with cogeneration the fuel utiliuzation is more efficient and optimized and hence more economical.
Need for Cogeneration
Cogeneration helps to improve the efficiency of the plant.
Cogeneration reduce air emissions of particulate matter, nitrous oxides, sulphur dioxide, mercury and carbon dioxide which would otherwise leads to greenhouse effect.
It reduces cost of production and improve productivity.
Cogeneration system helps to save water consumption and water costs.
Cogeneration system is more economical as compared to conventional power plant.
Types of Cogeneration Power Plants
In a typical Combined heat and power plant system there is a steam or gas turbine which take steam and drives an alternator. A waste heat exchanger is also installed in cogeneration plant, which recovers the excess heat or exhaust gas from the electric generator to in turn generate steam or hot water.
There are basically two types of cogeneration power plants, such as-
Topping cycle power plant
Bottoming cycle power plant
Topping Cycle Power Plant
In this type of Combine Heat and Power plant electricity is generated first and then waste or exhaust steam is used to heating water or building. There are basically four types of topping cycles.
Combined-cycle topping CHP plant- In this type of plant the fuel is firstly burnt in a steam boiler. The steam so produced in a boiler is used to drive turbine and hence synchronous generator which in turn produces electrical energy. The exhaust from this turbine can be either used to provide usable heat, or can be send to a heat recovery system to generate steam, which maybe further used to drive a secondary steam turbine.
Steam-turbine topping CHP Plant- In this the fuel is burned to produce steam, which generates power. The exhaust steam is then used as low-pressure process steam to heat water for various purposes.
Water turbine topping CHP Plant- In this type of CHP plant a jacket of cooling water is run through a heat recovery system to generate steam or hot water for space heating.
Gas turbine topping CHP plant- In This topping plant a natural gas fired turbine is used to drives a synchronous generator to produce electricity. The exhaust gas is sent to a heat recovery boiler where it is used to convert water into steam, or to make usable heat for heating purposes.
Bottoming Cycle Power Plant
As its name indicate bottoming cycle is exactly opposite of topping cycle. In this type of CHP plant the excess heat from a manufacturing process is used to generate steam, and this steam is used for generating electrical energy. In this type of cycle no extra fuel is required to produce electricity, as fuel is already burnt in production process.
Configuration of Cogeneration Plant
Gas turbine Combine heat power plants which uses the waste heat in the flue gas emerging out of gas turbines.
Steam turbine Combine heat power plants that use the heating system as the jet steam condenser for the steam turbine.
Molten-carbonate fuel cells have a hot exhaust, very suitable for heating.
Combined cycle power plants adapted for Combine Heat and Power.
Statement: Respect the original, good articles worth sharing, if there is infringement please contact delete.
