Mga Key Technologies sa Low-Voltage DC Solid-State Circuit Breakers

1 Teknikal nga mga Hamon

1.1 Katatagan sa Pagkonekta sa Paralelo sa mga Device
Sa praktikal nga aplikasyon, ang kantidad sa kuryente nga makakarga sa usa ka power electronic device mao'y relatyibong limitado. Aron mapasabot ang mataas nga kuryente, kasagaran gigamit ang paralel nga koneksyon sa daghang mga device. Apan, ang pagkakaiba sa mga parametro sa mga device—tulad sa kaunting pagkakaiba sa on-resistance ug threshold voltage—makapukaw og dili parehas nga distribusyon sa kuryente sa panahon sa operasyon sa paralelo. Sa panahon sa switching transients, ang parasitic inductance ug capacitance makapukaw pa og dili parehas nga rate sa pagbag-o sa kuryente sa mga parallel nga device, nagpadayon pa sa pagwala sa balanse sa kuryente. Kung wala ma-address niini ngadto sa agad, mahimong mag-heat ug mag-fail ang uban nga mga device tungod sa labi nga kuryente, sumala sa pagbawas sa serbisyo nga buhok sa solid-state circuit breaker.

1.2 Pagdelay sa Pag-detect sa Fault
Sa DC systems, ang katangian sa fault current niana dako kaayo ang kalainan gikan sa AC systems, walay zero-crossing points nga makatabang sa pag-detect ug pag-interrupt sa fault. Kini nagkinahanglan sa solid-state circuit breakers nga gamiton ang microsecond-level nga algoritmo sa pag-detect sa fault aron mas precise nga matun-an ang mga fault ug mobati sa agad. Ang tradisyonal nga mga paraan sa pag-detect sa fault adunay dako kaayo nga delay sa pag-atiman sa rapiyang nag-usab nga DC fault currents, diin dili na maka-abot sa panginahanglan sa fast protection.

1.3 Kontradiksyon Tungod sa Heat Dissipation ug Volume
Arong mapasabot ang panginahanglan sa modernong power systems sa mataas nga power density, ang disenyo sa solid-state circuit breaker kinahanglan mas sayo nga power handling sa limited nga espasyo. Apan, ang mas taas nga power density nagresulta sa dako kaayo nga increase sa heat nga giproduktsohan sa power electronic devices. Ang insufisyanse nga heat dissipation nagresulta sa labi nga temperatura, nagdegrade sa performance sa device ug posibleng mag-trigger og thermal runaway ug pag-fail sa equipment. Ang tradisyonal nga mga teknik sa pagsulyap sa heat dili maayo ang performans sa high-power-density nga solid-state breakers. Ang liquid cooling makapabor sa pag-improve sa efficiency sa heat dissipation, apan nakapadayon sa size ug cost sa equipment. Busa, paunsaon ang efektibo nga pagsulyap sa heat kasama ang reasonable nga volume control—maabot ang synergistic optimization—usa ka key challenge sa disenyo sa solid-state circuit breaker.

2 Key Technology Research

2.1 Wide-Bandgap Device Application Technology
(1) SiC MOSFET Selection and Packaging
Among various wide-bandgap devices, low-conduction-loss SiC MOSFETs offer significant advantages. To enhance their performance in multi-device parallel applications, a symmetrical Direct Bonded Copper (DBC) layout is adopted. This layout effectively reduces parasitic inductance, which is crucial for improving device switching characteristics. During switching, especially at turn-off, interaction between parasitic inductance and device capacitance causes gate voltage oscillation. Experimental tests show that with a symmetrical DBC layout, gate voltage oscillation during turn-off can be controlled to less than 5%. This not only improves dynamic stability during parallel operation but also reduces the risk of device damage caused by voltage oscillation.

(2) Dynamic Current Sharing Control
To address the challenge of current imbalance in parallel devices, a control strategy combining a current-sharing bus with adaptive PI regulation is introduced. The current-sharing bus, through unique structural design, provides a balanced current distribution path for each parallel branch at the physical level. On this basis, an adaptive PI regulation algorithm dynamically adjusts the drive signals of each device based on real-time monitoring of branch currents, achieving more precise current sharing control.

2.2 Fast Fault Detection and Interruption Technology
(1) Fault Detection Based on Gate Voltage
Analysis of SiC MOSFET short-circuit characteristics reveals that during a short-circuit fault, the drain-source voltage (VDS) rapidly spikes to 900V while the gate voltage significantly drops with a slope exceeding 10 V/ns. Leveraging this characteristic, a dual-threshold comparator is designed for rapid fault detection, setting two current thresholds: Ith1 = 500 A and Ith2 = 1.2 kA. When the detected current exceeds Ith1, a preliminary warning is triggered; exceeding Ith2 indicates a confirmed short-circuit fault. The designed detection circuit and signal processing algorithm achieve a detection delay of only 0.8 μs. This approach bypasses the complex signal conversion and processing of traditional methods by utilizing the SiC MOSFET's inherent electrical characteristics, significantly improving fault detection accuracy.

(2) Multi-Objective Optimized Interruption Strategy
To achieve high-performance fault interruption in solid-state circuit breakers, interruption time (Δt), energy absorption (EMOV), and inrush current (Ipeak) are set as objective functions, optimized using a multi-objective particle swarm optimization (MOPSO) algorithm. Shorter interruption time provides better protection for system equipment; energy absorption affects the selection and lifespan of protective components like MOVs; excessive inrush current causes significant electrical stress, impacting normal equipment operation.

Through multiple iterations of MOPSO optimization, optimal parameters are determined: current-limiting inductor LB = 15 μH and MOV voltage-limiting coefficient γ = 1.8. Using these optimized parameters, the interruption time is reduced to 73.5 μs, and the maximum current is limited to 526 A. To visually demonstrate the optimization effect, the TOPSIS decision-making method compares results before and after optimization. The comparison shows significant improvements in key indicators such as interruption time, energy absorption, and inrush current, greatly enhancing overall performance and better meeting practical engineering requirements for fast and reliable interruption by solid-state circuit breakers.

2.3 High-Reliability Mechanical Structure Design
(1) Permanent Magnet Isolator Switch
To improve the reliability and stability of solid-state circuit breakers, a permanent magnet isolator switch employing a bistable permanent magnet mechanism is designed. In this structure, the holding force for closing and opening is primarily provided by permanent magnets, with the coil energized only momentarily during switching operations. This reduces power consumption by approximately 90% compared to traditional electromagnetic isolator switches. Adams dynamic simulation analysis shows that the mechanical life of this permanent magnet isolator switch exceeds 1 million operations, with a contact separation speed of 3 m/s. The high contact separation speed ensures rapid circuit disconnection upon fault occurrence, reducing the likelihood of arc generation and enhancing the switch's interruption capability. The long mechanical life ensures stable performance over extended use, reducing maintenance and replacement frequency, thus providing strong support for the efficient operation of the solid-state circuit breaker.

(2) Thermal Management Solution
To address heat dissipation challenges in high-power-density designs, a hybrid cooling solution combining evaporative cooling with forced air cooling is proposed. Evaporative cooling utilizes the principle of liquid evaporation absorbing heat, enabling efficient heat transfer within compact spaces. Forced air cooling further enhances heat dissipation through fan-driven forced convection. This hybrid cooling method stabilizes the module's hotspot temperature below 75°C, with a temperature rise rate of less than 5°C/min, meeting standard requirements.III. Experimental Verification

3 Experimental Verification

3.1 Prototype Parameters
To verify the effectiveness of the key technologies and design schemes, a prototype of a low-voltage DC solid-state circuit breaker was developed, with the main parameters as follows:

3.2 Type Test Results

Comprehensive type tests were conducted on the prototype to evaluate whether its performance meets the requirements for practical applications:

(1) Short-Circuit Interruption Test
Short-circuit faults are among the most severe fault types in power systems, and the enormous instantaneous current they generate poses a significant threat to equipment operation. To simulate this extreme condition, a 23 kA short-circuit current test environment was established—posing a rigorous challenge for the solid-state circuit breaker. At the start of the test, the prototype rapidly activated, and its built-in fast fault detection and interruption technology began to function. This technology, through high-precision current monitoring and a rapid response mechanism, detected the abnormal current within an extremely short time and immediately triggered the interruption process.

During interruption, test personnel closely observed the breaker's performance, and no arc re-ignition occurred throughout the process. This result not only demonstrates the high efficiency of the fast fault detection and interruption technology but also highlights the solid-state circuit breaker's superior interruption performance. In traditional circuit breakers, arc re-ignition is a difficult-to-avoid issue that often leads to secondary faults or even severe equipment damage. By contrast, the solid-state circuit breaker successfully avoids this problem through advanced interruption techniques, thereby providing strong support for the stable operation of power systems.

(2) Temperature Rise Test
Thermal performance is another key factor in evaluating solid-state circuit breakers. To effectively assess the device's heat dissipation capability during prolonged operation, a temperature rise test was conducted. The prototype was required to operate continuously for 24 hours, during which significant heat was generated [9]. After the test, temperature sensors were used to measure the prototype's temperature. The results showed a temperature rise of ΔT = 32 K. This data confirms the effectiveness of the hybrid cooling solution combining evaporative cooling and forced air cooling. By integrating the natural heat dissipation principle of evaporative cooling with the forced convection of forced air cooling, the system efficiently dissipates heat generated during operation, ensuring the device remains within an acceptable temperature range. Good thermal management not only ensures stable operation of the solid-state circuit breaker but also extends its service life.

(3) Lifetime Test
Service life is a critical indicator for determining whether a solid-state circuit breaker can be widely applied in real power systems. Therefore, to verify its lifespan performance, the prototype underwent an endurance test of one million operational cycles. Throughout the test, personnel closely monitored changes in the contact resistance of the prototype. After the test, contact resistance was measured and found to have changed by less than 5%. This result validates the effectiveness of the long-life design of the permanent magnet isolator switch. Even after prolonged and frequent operations, the switch contacts maintain excellent conductivity, ensuring reliable on/off functionality of the solid-state circuit breaker.

4 Conclusion
In summary, this paper presents a technical solution for low-voltage DC solid-state circuit breakers based on in-depth research into key technologies, including optimization of wide-bandgap devices, intelligent control algorithms, and high-reliability structural design. Experimental validation shows that the developed prototype achieves leading performance in key indicators such as interruption speed, fault detection accuracy, and operational lifespan.

It successfully realizes microsecond-level fast interruption and a million-cycle operational life, providing a practical and feasible solution for protection in new energy power distribution systems. Looking ahead, there are many promising research directions for low-voltage DC solid-state circuit breakers. For example, establishing a device-packaging-system level integrated simulation model could more comprehensively simulate the performance of solid-state circuit breakers under various operating conditions, thereby providing more accurate theoretical support for design optimization.