Ga abụọkachasị obere nke ọnụọgụ na mmalite eme ka ọsọ dị mkpa gbasara ihe niile ebe ọchịchịrị akwụkwọ osimiri dị otú ma ọ bụ ọtụtụ ntụkwasị obere bụrụkwa na-akwanyere IEE-Business
Core Solution Concept
Gwọrọ nke ọma site na mgbalị ihe dị mkpa maka ụbọchị electromagnetism, ịkewapụta ahịa magnetic saturation. Ekwupụta ọnụọgụgụ na-akpali ihe dị ka high-frequency currents, DC components, ma ọ bụ high-order harmonics, ezie na-enye ọṅụọgụ site na ụbọchị CTs n'otu iron-core mgbe ọ bụla na-egosi waveform kacha.
Technical Solution Architecture
- Sensing Unit: Flexible Air-Core Rogowski Coil
- Structural Innovations
- Wire enameled na-akpali mmadụ aka na-akpali uniform n'otu former flexible dị ka epoxy ma ọ bụ engineering plastic
- Design split-core mechanical na-ekwuokwa installation live ( dị ka ọ bụla na retrofit ma ọ bụ otu ụzọ pụrụ)
- Signal Generation Principle
⚠ Output Signal: di/dt (Current Differential Value)
➡ Na-akọwapụta directly ọnụọgụ nke current, ịkewapụta effects nke core hysteresis. - Signal Processing Unit: High-Performance Integrator Circuit
|
Core Module |
Technical Characteristics |
Performance Indicators |
|
Integrator Amplifier |
Ultra-low input bias current (≤1pA) |
Temp Drift: ±0.5μV/°C |
|
Integration Capacitor |
Polypropylene Film Capacitor (C0G grade) |
Capacitance Stability >99%@ -40~125°C |
|
Dynamic Compensation |
Adaptive feedback network |
Integrator Drift Suppression >40dB |
|
Bandwidth Extension |
Multi-stage active filtering |
Freq. Response: DC ~ 1MHz |
- ↳ Output Signal: Vout = k・I(t) (k is calibration factor, voltage linearly corresponds to current)
Core Advantages Over Traditional CTs
|
Pain Point Scenario |
Limitations of Traditional Iron-Core CTs |
Advantages of This Solution |
|
High Short-Circuit Current |
Measurement failure due to magnetic saturation |
No magnetic saturation |
|
DC Component |
Cannot measure steady-state DC |
Supports precise DC component measurement |
|
High-Frequency Harmonics |
High-frequency signal attenuation due to core losses |
<0.5% distortion @ 100kHz harmonic |
|
Complex Waveforms |
Phase delay and waveform distortion |
Group Delay <10ns |
|
Installation Flexibility |
Require power-off installation / Space-constrained |
Flexible split-core design, 3-second deployment |
Typical Application Scenarios
- Inverter Output Monitoring
- Precisely captures high-frequency oscillations caused by IGBT switching (e.g., 20-150kHz)
- Case: Harmonic analysis at a PV inverter plant, measurement error for 50th harmonic (2.5kHz) reduced from 12% to 0.8%.
- Arc Fault Detection
- Nanosecond response to microsecond-level pulse currents during arc initiation (>100A/μs)
- Application: Arc protection in data center distribution cabinets, response time shortened to 300μs.
- Electric Locomotive Traction Systems
- Simultaneous analysis of DC supply components and PWM carrier signals (carrier freq. 2-5kHz)
- Measured Data: Maintained Class 1 accuracy for DC 1500V + 4kHz ripple current.
Key Technical Parameters Summary
|
Item |
Parameter |
|
Measurement Range |
10mA ~ 100kA (Peak) |
|
Frequency Response |
DC – 1.5MHz (-3dB) |
|
Linearity Error |
≤ ±0.2% FS |
|
Mounting Bore |
Φ50mm ~ Φ300mm (Customizable) |
|
Operating Temp. |
-40℃ ~ +85℃ |
|
Safety Certs. |
IEC 61010, EN 50178 |
Solution Value Summary
Three-Dimensional Technological Breakthroughs:
- Physical Layer Innovation: Air-core structure completely eliminates magnetic saturation risk, lifespan increased 10x.
- Signal Layer Fidelity: 1MHz bandwidth + sub-microsecond response enables high-precision sensing for Energy IoT.
- Engineering Layer Convenience: Split-core design reduces O&M downtime costs by 90%.
