SAFE-MULTI E-stop Safety Selay
Key attributes
| Brand | Switchgear parts |
| Model NO. | SAFE-MULTI E-stop Safety Selay |
| Rated frequency | 50/60Hz |
| Series | SAFE |
Product descriptions from the supplier
SAFE-MULTI is a safety relay for emergency stop, safety door and light curtain monitoring up to SIL 3 and Cat. 4, PL e in accordance with EN 62061 / EN 61508 and EN ISO 13849, certified by TÜV Rheinland, 1- or 2-channel operation with or without cross circuit detection, automatic and manual start, 7 safe relay contacts, nominal input voltage: 24 V AC/DC, max. switching capacity 250 V AC / 6 A, pluggable screw terminal blocks
Safety relay for emergency stop buttons, safety door switches and light curtain monitoring
Function
7 safe relay contacts, 4 auxiliary contact, 2 PNP Outputs, 1- or 2-channel input, auto and manual start, up to SIL 3 / Cat. 4, PL e, 24 V AC/DC, width: 45 mm
Features
7 N/O Safety Contacts
4 N/C Auxiliary Contact
2 PNP Outputs
Double Channel Input
| Parameter | Specification |
|---|---|
| In compliance with | EN 60204-1; EN ISO 13849-1; IEC 62061 |
| Operating voltage | AC/DC 24 V +/- 10 % |
| Power consumption | AC 8.5 VA/DC 4.5 W |
| Rated supply frequency | 50 - 60 Hz |
| Safety contacts | 7 non-delayed safety contacts (NO) |
| Auxiliary contacts | 4 non-delayed auxiliary contact (NC) |
| Auxiliary transistor outputs (O1, O2) | DC 24 V/30 mA, over current protected |
| Max. switching voltage | AC 250 V |
| Contact rating of safety contacts (13-14, …, 73-74)
|
AC: 250 V, 2000 VA, 8 A for resistive load
|
| Max. total current through all
|
35 A with 10 mm spacing between the devices
|
| Contact rating of auxiliary contact | AC: 250 V, 2000 VA, 8 A for resistive load
|
| Minimum contact load | 5 V, 10 mA |
| External fuses | 10 A gG (NO); 6 A gG (NC) |
| Max. switch-on delay | < 30 ms |
| Max. switch-off delay | Via S12 or S13/S14 < 20 ms |
| Recovery time | < 500 ms |
| Max. length of control line | 2×1000 m at 1.5 mm², 2×500 m at 0.75 mm² |
| Wire width | 0.14 - 2.5 mm² |
| Tightening moment (Min./Max.) | 0.5 Nm/0.6 Nm |
| Contact material | AgSnO₂ |
| Service Life | mech. approx. 1×10⁷ |
| Rated impulse withstand voltage, leakage path/air gap | 4 kV (DIN VDE 0110-1) |
| Rated insulation voltage | 250 V |
| Degree of pollution/Overvoltage category | 2/3 (DIN VDE 0110-0) |
| Protection | IP20 |
| Temperature range Ambient | -15 °C to +40 °C |
| Temperature range Storage | -15 °C to +85 °C |
| Max. altitude | ≤ 2000 m (above sea level) |
| Weight approx. | 350 g |
Online store
On-time delivery rate
Response time
100.0%
≤4h
Company overview
Workplace: 1000m²
Total staff:
Highest Annual Export(usD): 300000000
Services
Business Type: Sales
Main Categories: Low Voltage Electrical Apparatus/Instrument meters/Tester/Production equipment/Electrical fittings/Equipment Parts
Whole life care manager
Whole-life care management services for equipment procurement, use, maintenance, and after-sales, ensuring safe operation of electrical equipment, continuous control, and worry-free electricity consumption.
The equipment supplier has passed platform qualification certification and technical evaluation, ensuring compliance, professionalism, and reliability from the source.
Related Products
-
GRW8-01 02 Temperature Monitoring Relay
-
Digital Timer Switch TS-GE2 Programmable Periodic Timer
-
Digital Timer Switch THC 822 16A Weekly Programmable
-
Digital Timer Switch THC 109-16A Light Dependent Relay ＆accessories
-
Digital Timer Switch THC 109B-16A Light Dependent Relay ＆accessories
-
Digital Timer Switch THC 15A Programmable Periodic Timer
-
Digital Timer Switch THC 20-1C Weekly Programmable
Related Knowledges
-
How to Identify Internal Faults in a Transformer?Measure DC resistance: Use a bridge to measure the DC resistance of each high- and low-voltage winding. Check whether the resistance values among phases are balanced and consistent with the manufacturer’s original data. If phase resistance cannot be measured directly, line resistance may be measured instead. The DC resistance values can indicate whether the windings are intact, whether there are short circuits or open circuits, and whether the contact resistance of the tap changer is normal. IfFelix Spark11/04/2025 -
Front-Panel Visible Wiring Standards for Electrical Control PanelsFront-panel visible wiring: During manual wiring (not using templates or molds), wiring must be straight, neat, closely attached to the mounting surface, rationally routed, and with secure connections that facilitate maintenance. Wiring channels should be minimized as much as possible. Within the same channel, bottom-layer conductors shall be grouped by main and control circuits, arranged in a single-layer parallel dense layout or bundled, and kept closely attached to the mounting surface. ConduJames11/04/2025 -
What are the requirements for inspecting and maintaining a transformer's no-load tap changer?The tap changer operating handle shall be equipped with a protective cover. The flange at the handle shall be well sealed with no oil leakage. Locking screws shall securely fasten both the handle and the drive mechanism, and the handle rotation shall be smooth without binding. The position indicator on the handle shall be clear, accurate, and consistent with the tap voltage regulation range of the winding. Limit stops shall be provided at both extreme positions. The insulating cylinder of the tLeon11/04/2025 -
What Are the Common Inverter Fault Symptoms and Inspection Methods? A Complete GuideCommon inverter faults mainly include overcurrent, short circuit, ground fault, overvoltage, undervoltage, phase loss, overheating, overload, CPU malfunction, and communication errors. Modern inverters are equipped with comprehensive self-diagnostic, protection, and alarm functions. When any of these faults occurs, the inverter will immediately trigger an alarm or shut down automatically for protection, displaying a fault code or fault type. In most cases, the fault cause can be quickly identifiFelix Spark11/04/2025 -
What are the causes of dielectric withstand failure in vacuum circuit breakers?Causes of Dielectric Withstand Failure in Vacuum Circuit Breakers: Surface contamination: The product must be thoroughly cleaned before dielectric withstand testing to remove any dirt or contaminants.Dielectric withstand tests for circuit breakers include both power-frequency withstand voltage and lightning impulse withstand voltage. These tests must be performed separately for phase-to-phase and pole-to-pole (across the vacuum interrupter) configurations.Circuit breakers are recommended to be tFelix Spark11/04/2025 -
What Are the Top 10 Taboos and Precautions in the Installation of Distribution Boards and Cabinets?There are many taboos and problematic practices in the installation of distribution boards and cabinets that must be noted. Especially in certain areas, improper operations during installation may lead to serious consequences. For cases where the precautions were not followed, some corrective measures are also provided here to remedy previous mistakes. Let’s follow along and take a look at common installation taboos from manufacturers regarding distribution boxes and cabinets!1. Taboo: LightingJames11/04/2025
Haven't found the right supplier yet? Let matching verified suppliers find you.
Get Quotation Now
Send inquiry
Download
Get the IEE Business Application
Use the IEE-Business app to find equipment, obtain solutions, connect with experts, and participate in industry collaboration anytime, anywhere—fully supporting the development of your power projects and business.
