• Product
  • Suppliers
  • Manufacturers
  • Solutions
  • Free tools
  • Knowledges
  • Experts
  • Communities
Search


Wind Energy Electricity Generation

Electrical4u
Electrical4u
Field: Basic Electrical
0
China

WechatIMG1814.jpeg

Wind energy simply means kinetic energy of air in motion. Air flows on the earth due to uneven heating of the earth surface by radiant energy from the sun.

There are many places on the earth where the wind always presents. As the wind is naturally available mechanical energy, we can use this wind to rotate generators to produce electricity. Basically generating electricity by rotating generators with the help of wind is known as wind energy electricity generation or simply wind power generation or wind electricity generation.

Wind Energy Electricity Generation System

Wind is a clean source of energy. It has no effect of the greenhouse on the atmosphere. It is a substitute for fossil fuels such as coal, petroleum and natural gas, etc. Although, coal, petroleum, and natural gas, etc. are the primary source of fuel for producing electricity, but the availability of such fossil fuel is limited. Globally, 67% of electricity generated from fossil fuels, 13% from nuclear energy and rest of 20% from a renewable energy source such as hydro energy, solar energy, wind energy, tidal energy, etc. So we see how much the world depends on fossil fuel for producing electricity and that is why we focus on wind and other renewable energy sources to generate electricity to overcome the dependence on fossil fuels. Running cost of producing electricity with wind energy is quite low. Once the turbines are installed, and there is no much maintenance required for a long time. Wind energy electricity generation system takes some land for installation, but we can use most of the land for cultivation. So land is not a big issue for wind turbine generating systems. In most of the cases, wind plants are installed at a good height to obtain sufficient wind to produce electricity. It is now the fastest growing electricity resource in the world.Vertical Axis Wind Turbine or VAWT or Horizontal Axis Wind Turbine or HAWT

One single wind turbine may not be able to produce the desired level of electricity. Hence, numbers wind turbines are connected together to obtain the desired output. This assembly of wind turbines together is called a wind farm. We must choose the place for constructing a wind farm where the wind speed is sufficient to move the blade of the turbine. When the wind blows through the blades of a turbine, the turbine rotates to run a generator to produce electricity. This electricity flows down through the cable attached to the turbine tower. This cable is also interconnected with cables from other wind turbines in the wind farm.

Hence, electricity from all wind turbines comes to a common node from where it is taken for further ends. After all, this electricity is used directly for domestic or industrial load or is drawn by any grid to fulfill the requirement of electricity.

Statement: Respect the original, good articles worth sharing, if there is infringement please contact delete.

Give a tip and encourage the author!
Recommended
Three-Phase SPD: Types, Wiring & Maintenance Guide
Three-Phase SPD: Types, Wiring & Maintenance Guide
1. What Is a Three-Phase Power Surge Protective Device (SPD)?A three-phase power surge protective device (SPD), also known as a three-phase lightning arrester, is specifically designed for three-phase AC power systems. Its primary function is to limit transient overvoltages caused by lightning strikes or switching operations in the power grid, thereby protecting downstream electrical equipment from damage. The SPD operates based on energy absorption and dissipation: when an overvoltage event occ
James
12/02/2025
Railway 10kV Power Through Lines: Design & Operation Requirements
Railway 10kV Power Through Lines: Design & Operation Requirements
The Daquan Line has a large power load, with numerous and scattered load points along the section. Each load point has a small capacity, with an average of one load point every 2-3 km, so two 10 kV power through lines should be adopted for power supply. High-speed railways use two lines for power supply: primary through line and comprehensive through line. The power sources of the two through lines are taken from the dedicated bus sections fed by the voltage regulators installed in each power di
Edwiin
11/26/2025
Analysis of Causes of Power Line Loss and Loss Reduction Methods
Analysis of Causes of Power Line Loss and Loss Reduction Methods
In power grid construction, we should focus on actual conditions and establish a grid layout suitable for our own needs. We need to minimize power loss in the grid, save social resource investment, and comprehensively improve China's economic benefits. Relevant power supply and electricity departments should also set work goals centered on effectively reducing power loss, respond to energy conservation calls, and build green social and economic benefits for China.1.Current Status of China's Powe
Echo
11/26/2025
Neutral Grounding Methods for Conventional-Speed Railway Power Systems
Neutral Grounding Methods for Conventional-Speed Railway Power Systems
Railway power systems primarily consist of automatic block signaling lines, through-feeder power lines, railway substations and distribution stations, and incoming power supply lines. They provide electricity to critical railway operations—including signaling, communications, rolling stock systems, station passenger handling, and maintenance facilities. As an integral part of the national power grid, railway power systems exhibit distinct characteristics of both electrical power engineering and
Echo
11/26/2025
Send inquiry
Download
Get the IEE Business Application
Use the IEE-Business app to find equipment, obtain solutions, connect with experts, and participate in industry collaboration anytime, anywhere—fully supporting the development of your power projects and business.