Kriştal Oşîlasyonê: Bîrkarî, Frekansa & Pîvanca Xerîdarê
Kîşeyên crystal li ser prînsîpa inverse piezoelectric effect dike derbas da ku dîrokên alternatîfê yên di navbera yanê crystalê de hatine têne şînandin, yanê crystalê di heman rêza naturalê de hatine lalikan. Heke wan vibrasyonan bi vê yekemîna hatine guherand bêtirin.
Ev kîşeyan zeviyên Quartz crystal hatine jînandin, her û bisdehê wê ne qad rochelle salt û tourmaline piyezoelektrik effect dike xweşk kirin, la'man quartz ên pêşniyar, berdest û mekanîkî gir û nîvend e.
Di kîşeyên crystalan de, crystal li ser îro dikare yên du metallic plates dike têne sernivîse (wê ji Figure 1a re hatine nîşan kirin) û electrical equivalent ya wê ji Figure 1b re hatine nîşan kirin. Di realiteyê de, crystal li ser îro dikare yên series RLC circuit dike têne formkirin, ku ji komponentan hatine têne formkirin.
Resistor RS bi nîvendî
Inductor LS bi nîvendî
Capacitor CS bi nîvendî
Yanê li ser îro dikare yên capacitance û electrodes Cp.
Li ser îro dikare yên Cp, crystal li ser îro dikare yên two different frequencies viz.,
Series Resonant Frequency, fs ku dike derbas da ku series capacitance CS resonates bi series inductance LS. Li ser îro dikare yên impedance ya crystal ên pêşniyar e û feedback ên pêşniyar e. Mathematical expression for the same is given as
Parallel Resonant frequency, fp ku dike derbas da ku reactance ya LSCS leg equals reactance ya parallel capacitor Cp i.e. LS û CS resonate bi Cp. Li ser îro dikare yên impedance ya crystal ên pêşniyar e û feedback ên pêşniyar e. Mathematically it can be given as
Behaviour of the capacitor will be capacitive both below fS and above fp. However for the frequencies which lie in-between fS and above fp, the crystal’s behavior will be inductive. Further when the frequency becomes equal to parallel resonant frequency fp, then the interaction between LS and Cp would form a parallel tuned LC tank circuit. Hence, a crystal can be viewed as a combination of series and parallel tuned resonance circuits due to which one needs to tune the circuit for any one among these two. Moreover it is to be noted that fp will be higher than fs and the closeness between the two will be decided by the cut and the dimensions of the crystal in-use.
Kîşeyên crystal can be designed by connecting the crystal into the circuit such that it offers low impedance when operated in series-resonant mode (Figure 2a) and high impedance when operated in anti-resonant or parallel resonant mode (Figure 2b).
In the circuits shown, the resistors R1 and R2 form the voltage divider network while the emitter resistor RE stabilizes the circuit. Further, CE (Figure 2a) acts as an AC bypass capacitor while the coupling capacitor CC (Figure 2a) is used to block DC signal propagation between the collector and the base terminals.
Next, the capacitors C1 and C2 form the capacitive voltage divider network in the case of Figure 2b. In addition, there is also a Radio Frequency Coil (RFC) in the circuits (both in Figure 2a and 2b) which offers dual advantage as it provides even the DC bias as well as frees the circuit-output from being affected by the AC signal on the power lines.
On supplying the power to the oscillator, the amplitude of the oscillations in the circuit increases until a point is reached wherein the nonlinearities in the amplifier reduce the loop gain to unity.
Next, on reaching the steady state, the crystal in the feedback loop highly influences the frequency of the operating circuit. Further, here, the frequency will self-adjust so as to facilitate the crystal to present a reactance to the circuit such that the Barkhausen phase requirement is fulfilled.
In general, the frequency of the crystal oscillators will be fixed to be the crystal’s fundamental or characteristic frequency which will be decided by the physical size and shape of the crystal.
However, if the crystal is non-parallel or of non-uniform thickness, then it might resonate at multiple frequencies, resulting in harmonics.
Further, the crystal oscillators can be tuned to either even or odd harmonic of the fundamental frequency, which are called Harmonic and Overtone Oscillators, respectively.
An example of this is the case where the parallel resonance frequency of the crystal is decreased or increased by adding a capacitor or an inductor across the crystal, respectively.
The typical operating range of the crystal oscillators is from 40 KHz to 100 MHz wherein the low frequency oscillators are designed using OpAmps while the high frequency-ones are designed using the transistors (BJTs or FETs).
The frequency of oscillations generated by the circuit is decided by the series resonant frequency of the crystal and will be unaffected by the variations in supply voltage, transistor parameters, etc. As a result, crystal oscillators exhibit a high Q-factor with excellent frequency stability, making them most suitable for high-frequency applications.
However, care should be taken so as to drive the crystal with optimum power only. This is because, if too much power is delivered to the crystal, then the parasitic resonances might be excited in the crystal which leads to the unstable resonant frequency.
Further, even its output waveform might be distorted due to the degradation in its phase noise performance. Moreover, it can even result in the destruction of the device (crystal) due to overheating.
Kîşeyên crystal are compact in size and are of low cost due to which they are extensively used in electronic warfare systems, communication systems, guidance systems, microprocessors, microcontrollers, space tracking systems, measuring instruments, medical devices, computers, digital systems, instrumentation, phase-locked loop systems, modems, sensors, disk drives, marine systems, telecommunications, engine control systems, clocks, Global Positioning Systems (GPS), cable television systems, video cameras, toys, video games, radio systems, cellular phones, timers, etc.
Statement: Respect the original, good articles worth sharing, if there is infringement please contact delete.
