ROCKWILL H59 Grounding Transformer Solution: Zig-Zag Winding & Smart Monitoring for Neutral Grounding Systems
ROCKWILL H59 Grounding Transformer Solution: Zig-Zag Winding & Smart Monitoring for Neutral Grounding Systems
Application Scenarios:
Neutral point grounding in ungrounded or resonant grounded systems, limiting single-phase ground fault current, suppressing system overvoltage.
I. Core Design Solutions
- Customized Grounding Transformer
- Built on the H59 oil-immersed transformer platform, with high-voltage side using Zig-Zag windings or Yn-d connection to provide stable neutral grounding impedance.
- Complies with IEC 60076 and NF C52-112 standards, with insulation strength designed to withstand ground fault current surges.
- Key Parameters Configuration
|
Parameter |
Value/Specification |
|
Rated Voltage |
System voltage adaptation (6kV/10kV/20kV/33kV) |
|
Short-Time Overload |
Withstands 10–20× rated current for 10 seconds |
|
Zero-Sequence Impedance |
Customized per system capacitive current (Typical: 40Ω–100Ω) |
|
Connection Method |
Znyn11 or YNd11 |
- Grounding Method Selection
- Resistance Grounding: Secondary side connected to stainless steel grid resistor cabinets, limiting fault current to a safe range (Optional: 200A–2000A).
- Arc Suppression Coil Grounding: Paired with automatic tuning arc suppression coils to extinguish fault-point arcs.
II. Technical Advantages
- Reliable Structure & Protection
- Fully sealed oil tank: IP23 protection rating, suitable for outdoor installation (–25℃ to +50℃).
- Epoxy resin bushings: High-voltage side uses 33kV-grade T-type cable terminations (EPDM material), ensuring insulation reliability in humid environments.
- Intelligent Monitoring System
- Integrated DGPT2/DMCR protection relays for real-time monitoring of:
✓ Neutral point current/voltage
✓ Oil temperature (55℃ max. temperature rise)
✓ Oil level & pressure transients
✓ Fault gases (H₂, CH₄) content. - High Efficiency & Energy Saving
- Copper windings + ONAN cooling: No-load loss ≤0.2% of rated capacity (e.g., 1300W for 630kVA).
- Efficiency >98.5% (at full load, cosφ=1), meeting green grid standards.
III. Engineering Adaptation Services
- Customized Configuration
- Bushings creepage distance customized for altitude (>1000m requires reinforced insulation) and pollution levels.
- Optional add-ons:
- 5-position non-excitation tap changer (±2×2.5%)
- Stainless oil valves & anti-vibration roller bases.
IV. Typical Case Parameters
|
Capacity (kVA) |
System Voltage (kV) |
Zero-Seq. Impedance (Ω) |
Resistor Current (A) |
Protection Device |
|
300 |
20 |
60 |
400 |
DGPT2 + Thermostat |
|
500 |
33 |
85 |
800 |
DMCR + Gas Relay |
V. Service Commitment
- 10-year warranty: Lifelong maintenance for seals and windings.
- 48-hour response: Technical support hotline +86 577 27869969.
- Documentation provided: Grounding calculation reports, type test certificates (including temperature rise & short-circuit tests).
Note: This solution requires user-provided parameters (e.g., system short-circuit capacity, capacitive current) for precision engineering. Rockwill engineers will customize designs accordingly.
06/13/2025
Recommended
Integrated Wind-Solar Hybrid Power Solution for Remote Islands
AbstractThis proposal presents an innovative integrated energy solution that deeply combines wind power, photovoltaic power generation, pumped hydro storage, and seawater desalination technologies. It aims to systematically address the core challenges faced by remote islands, including difficult grid coverage, high costs of diesel power generation, limitations of traditional battery storage, and scarcity of freshwater resources. The solution achieves synergy and self-sufficiency in "power suppl
An Intelligent Wind-Solar Hybrid System with Fuzzy-PID Control for Enhanced Battery Management and MPPT
AbstractThis proposal presents a wind-solar hybrid power generation system based on advanced control technology, aiming to efficiently and economically address the power needs of remote areas and special application scenarios. The core of the system lies in an intelligent control system centered around an ATmega16 microprocessor. This system performs Maximum Power Point Tracking (MPPT) for both wind and solar energy and employs an optimized algorithm combining PID and fuzzy control for precise
Cost-Effective Wind-Solar Hybrid Solution: Buck-Boost Converter & Smart Charging Reduce System Cost
AbstractThis solution proposes an innovative high-efficiency wind-solar hybrid power generation system. Addressing core shortcomings in existing technologies—such as low energy utilization, short battery lifespan, and poor system stability—the system employs fully digitally controlled buck-boost DC/DC converters, interleaved parallel technology, and an intelligent three-stage charging algorithm. This enables Maximum Power Point Tracking (MPPT) over a wider range of wind speeds and s
Hybrid Wind-Solar Power System Optimization: A Comprehensive Design Solution for Off-Grid Applications
Introduction and Background1.1 Challenges of Single-Source Power Generation SystemsTraditional standalone photovoltaic (PV) or wind power generation systems have inherent drawbacks. PV power generation is affected by diurnal cycles and weather conditions, while wind power generation relies on unstable wind resources, leading to significant fluctuations in power output. To ensure a continuous power supply, large-capacity battery banks are necessary for energy storage and balance. However, bat
