Electrical Engineering Guides

Transformer Standards

Micro-Mechanism Analysis of Distribution Transformer Losses and Technical Pathway Selection under the New GB 20052-2024 Energy Efficiency Standard.

1. Core Logic: Deep Decomposition of Loss Mechanisms Distribution transformer losses are primarily categorized into No-load loss ( P0 P 0 ) and Load loss ( Pk P k ). To achieve a leap in energy efficiency (e.g., from Grade 3 to Grade 1), one must start with micro-mechanisms. 1.1 No-load Loss ( P

By Rockwill 04/24, 2026
DC Charging Pile Selection

Analysis of DC Charging Pile Terminal Overheating and Copper Aluminum Transition Standards

1. Requirements and Scope In the operation of high-power DC charging stations (120kW 360kW), site managers often encounter charred cable insulation, localized melting, or even equipment fires at the connection points. These failures typically occur where aluminum cables meet the copper busbars insid

By RW Energy 04/17, 2026
Power transformer

Quality Standards for Core Maintenance of Power Transformers

Transformer Core Inspection and Assembly Requirements The iron core should be flat with intact insulation coating, tightly stacked laminations, and no curling or waviness at the edges of silicon steel sheets. All core surfaces must be free of oil, dirt, and impurities. There should be no short circu

By Oliver Watts 12/17, 2025
Power transformer

How to Implement Transformer Gap Protection & Standard Shutdown Steps

How to Implement Transformer Neutral Grounding Gap Protection Measures? In a certain power grid, when a single-phase ground fault occurs on a power supply line, both the transformer neutral grounding gap protection and the power supply line protection operate simultaneously, causing an outage of an

By Noah 12/05, 2025
Gas Insulated Switchgear(GIS)

GIS Dual Grounding & Direct Grounding: State Grid 2018 Anti-Accident Measures

1. Regarding GIS, how should the requirement in Clause 14.1.1.4 of the State Grid’s "Eighteen Anti-Accident Measures" (2018 Edition) be understood? 14.1.1.4: The neutral point of a transformer shall be connected to two different sides of the main mesh of the grounding grid via two grounding down con

By Echo 12/05, 2025
Surge arrester fuse insulator

Three IEC standards in the insulator field, led by China, have been released.

Recently, three IEC standards on insulators, led by China for the first time, have been officially published. These standards primarily address the coupling markings, dimensions, and tests of insulator end fittings, specifically including IEC 60120:2020, IEC 60372:2020, and IEC 60471:2020. These thr

By Baker 11/29, 2025
Switch Disconnectors

Research on Quality Control and Acceptance Standards for Installation of GW4-126 Disconnector

1.Working Principle and Structural Features of GW4-126 Disconnector The GW4-126 disconnector is suitable for AC 50/60 Hz power lines with a rated voltage of 110 kV. It is used to disconnect or connect high-voltage circuits under no-load conditions, enabling circuit switching, operational mode change

By James 11/17, 2025
Gas Insulated Switchgear (GIS)

North American Standards: A Comparison Between IEEE and Chinese Switchgear Standards

IEEE Std C37.20.9™ defines the design, testing, and installation requirements for metal-enclosed gas-insulated switchgear (MEGIS) using gas at pressures above ambient as the primary insulation medium for alternating current systems rated from 1 kV to 52 kV. This includes, but is not limited to, circ

By James 11/10, 2025
Electrical Control Panels

Front-Panel Visible Wiring Standards for Electrical Control Panels

Front-panel visible wiring: During manual wiring (not using templates or molds), wiring must be straight, neat, closely attached to the mounting surface, rationally routed, and with secure connections that facilitate maintenance. Wiring channels should be minimized as much as possible. Within the sa

By James 11/04, 2025
Power Systems

THD Measurement Error Standards for Power Systems

Error Tolerance of Total Harmonic Distortion (THD): A Comprehensive Analysis Based on Application Scenarios, Equipment Accuracy, and Industry Standards The acceptable error range for Total Harmonic Distortion (THD) must be evaluated based on specific application contexts, measurement equipment accur

By Edwiin 11/03, 2025
Power Quality Monitors

What are the standards for calibration of online power quality monitoring devices?

Core Standards for Calibration of Online Power Quality Monitoring Devices The calibration of online power quality monitoring devices follows a comprehensive standard system, encompassing mandatory national standards, industry technical specifications, international guidelines, and requirements for c

By Edwiin 10/30, 2025
SF6 gas density relay

On-Site Testing of SF6 Gas Density Relays: Relevant Issues

Introduction SF6 gas is widely used as an insulating and arc-quenching medium in high-voltage and extra-high-voltage electrical equipment due to its excellent insulation, arc-extinguishing properties, and chemical stability. The insulation strength and arc-quenching capability of electrical equipmen

By Felix Spark 10/27, 2025

Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

All

Micro-Mechanism Analysis of Distribution Transformer Losses and Technical Pathway Selection under the New GB 20052-2024 Energy Efficiency Standard.

Analysis of DC Charging Pile Terminal Overheating and Copper Aluminum Transition Standards

Quality Standards for Core Maintenance of Power Transformers

How to Implement Transformer Gap Protection & Standard Shutdown Steps

GIS Dual Grounding & Direct Grounding: State Grid 2018 Anti-Accident Measures

Three IEC standards in the insulator field, led by China, have been released.

Research on Quality Control and Acceptance Standards for Installation of GW4-126 Disconnector

North American Standards: A Comparison Between IEEE and Chinese Switchgear Standards

Front-Panel Visible Wiring Standards for Electrical Control Panels

THD Measurement Error Standards for Power Systems

What are the standards for calibration of online power quality monitoring devices?

On-Site Testing of SF6 Gas Density Relays: Relevant Issues

Recommended Topics