Electrical Engineering Guides

Power Systems

What Are the Typical Wiring Diagrams of 35kV Lines？

Typical Wiring Diagram of 35kV Line Radial pi; Connection When a 35kV line adopts a radial power grid structure, a single - side power supply or a double - side power supply radial type can be used according to the situation of the power supply points, and a loop - out interval is reserved at the en

By Leon 07/18, 2025
Power Systems

What Is Fault Transfer Voltage and What Causes It in Low-Voltage Systems？

Fault Transfer Voltage In low - voltage distribution systems, there is a type of personal electric shock accident where the accident occurrence point and the system fault point are not at the same location. This kind of accident occurs because after a ground fault happens elsewhere, the generated fa

By Leon 07/18, 2025
Power Systems

Reactive Power Definition Measurement and Varmeter Principles

The power which exists in the circuit when the voltage and current are out of phase to each other, such type of power is known as the reactive power. The formula measures the reactive power in the circuit Reactive Power Measurement Varmeters Reactive power measurement is critical as it indicates cir

By Edwiin 07/17, 2025
Power Systems

What is a step voltage regulator?

Hey everyone, I'm Blue — an electrical engineer with over 20 years of experience, currently working at ABB. My career has mainly focused on circuit breaker design, transformer management, and providing power system solutions for various utility companies. Today, someone asked the question: "What is

By Master Electrician 07/11, 2025
Power Systems

Classification of Electric Power Distribution Network Systems

The typical electric power system network is categorized into three main components: generation, transmission, and distribution. Electric power is produced in power plants, which are often located far from load centers. As a result, transmission lines are employed to deliver power over long distance

By Edwiin 06/05, 2025
Power Systems

Why is the Ground Wire Always Positioned Above the Overhead Power Lines?

Ground Wire in Overhead Transmission Lines The ground wire (also called earth wire or OPGW) installed above phase lines in overhead transmission lines acts as a key protective and safety component. It provides lightning protection, ground fault defense, and helps prevent electrical system disruption

By Edwiin 06/04, 2025
Power Systems

What is the Power Angle in a Power Transmission Line?

The power angle, denoted by delta;, is the phase angle difference between two voltage levels in a power transmission line. Specifically, it represents the angular discrepancy between the sending-end voltage phasor and the receiving-end voltage (or between voltages at two bus points). In simpler term

By Edwiin 06/04, 2025
Power Systems

Permanent Magnet Moving Coil or PMMC Instrument

Definition Instruments that utilize a permanent magnet to generate a stationary magnetic field within which a coil moves are known as Permanent Magnet Moving Coil (PMMC) instruments. They operate on the principle that torque is exerted on a moving coil situated in the magnetic field of a permanent m

By Edwiin 05/30, 2025
Power Systems

Difference Between Porcelain and Glass Insulators

Key Differences Between Glass and Porcelain Insulators Both porcelain and glass insulators are widely applied in power transmission and distribution to insulate overhead line conductors from supporting towers and poles. With extended service lives and suitability for high voltage ratings, their uniq

By Edwiin 05/30, 2025
Power Systems

Comparison Between Overhead & Underground Transmission Systems

Key Differences and Comparison Between Underground and Overhead Power Transmission Distribution Public Safety In terms of public safety, underground systems outperform overhead transmission systems. With all transmission and distribution components buried, underground setups minimize risks from obst

By Edwiin 05/30, 2025
Power Systems

What is the Difference Between Shunt Reactor and Shunt Capacitor?

In an electrical power system, various devices are utilized to enhance power factor and operational efficiency. Shunt capacitors and shunt reactors represent two distinct components designed to optimize the performance of electrical grids. This article explores their key differences, beginning with

By Edwiin 05/30, 2025
Power Systems

What’s the difference in the circuit breaker for air - insulated vs gas - insulated?

Insulation Performance： Air - insulated Circuit Breakers : They use air as the insulating medium. The insulation performance of air is relatively limited. In harsh environments such as high humidity and high pollution, the insulation performance is easily affected. They are suitable for medium - and

By ABB 05/26, 2025

Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

All

What Are the Typical Wiring Diagrams of 35kV Lines？

What Is Fault Transfer Voltage and What Causes It in Low-Voltage Systems？

Reactive Power Definition Measurement and Varmeter Principles

What is a step voltage regulator?

Classification of Electric Power Distribution Network Systems

Why is the Ground Wire Always Positioned Above the Overhead Power Lines?

What is the Power Angle in a Power Transmission Line?

Permanent Magnet Moving Coil or PMMC Instrument

Difference Between Porcelain and Glass Insulators

Comparison Between Overhead & Underground Transmission Systems

What is the Difference Between Shunt Reactor and Shunt Capacitor?

What’s the difference in the circuit breaker for air - insulated vs gas - insulated?

Recommended Topics