Electrical Engineering Guides

Power Systems

Insulation Coordination in Power System

Insulation Coordination in Power System was introduced to arrange the electrical insulation levels of different components in the electrical power system including transmission network, in such a manner, that the failure of insulator , if occurs, confindes to the place where it would result in the l

By Electrical4u 03/23, 2024
Power Systems

Types of Insulators Used in Transmission (Overhead) Lines

Type of Insulators Used in Transmission lines There are 5 types of insulators used in transmission lines as overhead insulation: Pin Insulator Suspension Insulator Strain Insulator Stay Insulator Shackle Insulator Pin, Suspension, and Strain insulators are used in medium to high voltage systems. Wh

By Electrical4u 03/23, 2024
Power Systems

Electrical Insulator | Insulating Material | Porcelain Glass Polymer Insulator

What is an Electrical Insulator? An electrical insulator (also referred to as an insulator) is used in an electrical system to prevent unwanted flow of current to the earth from its supporting points. The insulator plays a vital role in the electrical system. An electrical insulator is a very high r

By Electrical4u 03/23, 2024
Power Systems

Dielectric Properties of Insulating Materials (Formula & Constant)

We can first go through the description of dielectric materials . It actually does not conduct electricity. They are insulators having very low electrical conductivity . So we have to know the difference between dielectric material and insulating material. The difference is that insulators block the

By Electrical4u 03/23, 2024
Power Systems

BIL or Basic Insulation Level Definition Table and Calculation

Basic Insulation Level Definition When lightning impulse over voltage appears in the system, it is discharged through surge protecting devices before the equipments of the system gets damaged. Hence, the insulation of such equipment must be designed to withstand a certain minimum voltage before the

By Electrical4u 03/23, 2024
Power Systems

Design of Foundations of Transmission Towers in different Soils

Design of Foundation of Transmission Towers in Different Soils All foundation shall be of RCC. The design and construction of RCC structures shall be carried out as per IS:456 and minimum grade of concrete shall be M-20. Limit state method of design shall be adopted. Cold twisted deformed bars as pe

By Electrical4u 03/22, 2024
Power Systems

Basic Concept of Transmission Tower Foundation

Foundation of any structure plays an important role in safety and satisfactory performance of the structure as it transmits mechanical loads of the electrical transmission system to earth. A transmission structure Without having a sound and safe foundation, it cannot perform the functions for which

By Electrical4u 03/22, 2024
Power Systems

Transmission Tower Erection Methodology

There are four main methods of the erection of steel transmission towers which are described below: Build-up method or Piecemeal method. Section method. Ground assembly method. Helicopter method. Build Up Method of Transmission Tower Erection This method is most commonly used in India for the erecti

By Electrical4u 03/22, 2024
Power Systems

Electrical Transmission Tower: Types, Design & Parts

What is a Transmission Tower? A transmission tower (also known as a power transmission tower, power tower, or electricity pylon) is a tall structure (usually a steel lattice tower) used to support an overhead power line. In electrical grids, they are used to carry high voltage transmission lines tha

By Electrical4u 03/22, 2024
Power Systems

Load Flow and Y Bus

Formation of Bus Admittance Matrix (Y bus ) S 1 , S 2 , S 3 are net complex power injections into bus 1, 2, 3 respectively y 12 , y 23 , y 13 are line admittances between lines 1-2, 2-3, 1-3 y 01sh /2, y 02sh /2, y 03sh /2 are half-line charging admittance between lines 1-2, 1-3 and 2-3 The half-lin

By Electrical4u 03/22, 2024
Power Systems

Inductance in Transmission Line

Reason of Transmission Line Inductance Generally, electric power is transmitted through the transmission line with AC high voltage and current . High valued alternating current while flowing through the conductor sets up magnetic flux of high strength with alternating nature. This high valued altern

By Electrical4u 03/22, 2024
Power Systems

Flexible AC Transmission Systems | FACTS

Flexible AC Transmission Systems (FACTS) – What and why? FACTS is the acronym for “Flexible AC Transmission Systems” and refers to a group of resources used to overcome certain limitations in the static and dynamic transmission capacity of electrical networks. The IEEE defines FACTS as alternating c

By Electrical4u 03/22, 2024

Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

All

Insulation Coordination in Power System

Types of Insulators Used in Transmission (Overhead) Lines

Electrical Insulator | Insulating Material | Porcelain Glass Polymer Insulator

Dielectric Properties of Insulating Materials (Formula & Constant)

BIL or Basic Insulation Level Definition Table and Calculation

Design of Foundations of Transmission Towers in different Soils

Basic Concept of Transmission Tower Foundation

Transmission Tower Erection Methodology

Electrical Transmission Tower: Types, Design & Parts

Load Flow and Y Bus

Inductance in Transmission Line

Flexible AC Transmission Systems | FACTS

Recommended Topics