Search

James Knowledge

Professionalism builds strength. As an expert in the installation and operation of electrical equipment, I am proficient in the installation process and strictly adhere to standards. I skillfully master the operation essentials and can swiftly eliminate faults. With a heart that constantly explores new knowledge, I illuminate the path to the efficient operation of electrical equipment.

Knowledge

Knowledge

How to Install a Three-Phase Voltage Regulator Safely

1. Pre-installation Preparation Installing a three-phase voltage regulator is a task that requires meticulous operation and strict adherence to specifications. Below is a detailed installation guide and key precautions: Selection and Matching Select an appropriately rated three-phase voltage regulat

By James 12/01, 2025
Knowledge

Three-Phase SPD: Types, Wiring & Maintenance Guide

1. What Is a Three-Phase Power Surge Protective Device (SPD)? A three-phase power surge protective device (SPD), also known as a three-phase lightning arrester, is specifically designed for three-phase AC power systems. Its primary function is to limit transient overvoltages caused by lightning stri

By James 12/02, 2025
Knowledge

Why Substation Grounding Transformers Trip? Fixes & Installation Guidelines

Substation grounding transformers require high accuracy, excellent anti-interference performance, high safety performance, reasonable structure, and good long-term stability to meet the requirements of substations for ground resistance measurement. At the same time, demands for communication and inf

By James 12/03, 2025
Knowledge

Brief Discussion on the Selection of Grounding Transformers in Booster Stations

Grounding transformers, commonly referred to as "grounding transformers" or simply "grounding units," operate under no-load conditions during normal grid operation and experience overload during short-circuit faults. Based on the filling medium, they are commonly categorized into oil-immersed and dr

By James 12/04, 2025
Knowledge

Wiring Methods and Parameters of Grounding Transformers

Grounding Transformer Winding Configurations Grounding transformers are classified by winding connection into two types: ZNyn (zigzag) or YNd. Their neutral points can be connected to an arc suppression coil or a grounding resistor. Currently, the zigzag (Z-type) grounding transformer connected via

By James 12/05, 2025
Knowledge

What Is an H61 Distribution Transformer? Uses & Setup

H61 distribution transformers refer to transformers used in power distribution systems. In a distribution system, high-voltage electricity must be converted into low-voltage electricity via transformers to supply electrical equipment in residential, commercial, and industrial facilities. The H61 dis

By James 12/08, 2025
Knowledge

Adjustment and Precautions for H61 Oil Power 26kV Electric Transformer Tap Changers

Preparatory Work Before Adjusting the Tap Changer of H61 Oil Power 26kV Electric Transformer Apply for and issue a work permit; carefully fill out the operation ticket; conduct a simulation board operation test to ensure the operation is error-free; confirm the personnel who will carry out and super

By James 12/08, 2025
Knowledge

Low-Voltage Distribution Lines and Power Distribution Requirements for Construction Sites

Low-voltage distribution lines refer to the circuits that, through a distribution transformer, step down the high voltage of 10 kV to the 380/220 V level—i.e., the low-voltage lines running from the substation to the end-use equipment. Low-voltage distribution lines should be considered during the d

By James 12/09, 2025
Knowledge

High-Voltage SF₆-Free Ring Main Unit: Adjustment of Mechanical Characteristics

(1) The contact gap is primarily determined by insulation coordination parameters, interruption parameters, contact material of the high-voltage SF₆-free ring main unit, and the design of the magnetic blowout chamber. In practical application, a larger contact gap is not necessarily better; instead,

By James 12/10, 2025
Knowledge

How to install a DTU on an N2 Insulation ring main unit?

DTU (Distribution Terminal Unit), a substation terminal in distribution automation systems, is secondary equipment installed in switching stations, distribution rooms, N2 Insulation ring main units (RMUs), and box-type substations. It bridges primary equipment and the distribution automation master

By James 12/11, 2025
Knowledge

Intelligent Substation Maintenance Pressure Plate Operation Guide

According to the "Eighteen Major Anti-Accident Measures for Power Grid of State Grid Corporation of China (Revised Edition)" promulgated in 2018, operation and maintenance units should improve the on-site operation regulations for intelligent substations, refine the usage instructions and abnormal h

By James 12/15, 2025
Knowledge

High Voltage Bushing Selection Standards for Power transformer

1. Structure Forms and Classification of Bushings The structure forms and classification of bushings are shown in the table below: Serial No. Classification Feature Category 1 Main insulation structure Capacitive Type Resin-impregnated paper Oil-impregnated paper Non-capacitive Type Gas insulation L

By James 12/20, 2025

Previous
1
2
···
4
5
6
7
8
9
10
11
Next