AIS VT/PT Dual-Enhanced Precision and Insulation Solution
Wone Store
2yrs +
staff 1000+m² US$300,000,000+ China
Core Objective: Precision Improvement and Insulation Reinforcement
Applicable Scenarios: Coastal power plants, chemical plants, high-humidity/high-pollution harsh environments
I. Technical Pain Points Analysis
Traditional AIS-VT faces two core issues in complex environments:
- Precision Drift:
- Dielectric constant variation due to humidity fluctuations and contaminant accumulation, causing secondary-side output error exceeding limits (>Class 0.5).
- Insulation Failure Risk:
- Surface flashover induced by salt mist/chemical pollutants, reducing breakdown voltage by >30%.
II. Innovative Technical Solutions
- Insulation System Upgrade: Nano-Composite Silicone Rubber Bushings
- Material Properties:
- Hydrophobicity lifespan ≥25 years (IEC 62073 accelerated aging verified), suppressing moisture penetration.
- Pollution flashover withstand voltage ↑40% (≥145 kV/m under salt fog test).
- Structural Optimization:
- Angled shed design + multi-level creepage extension, improving self-cleaning efficiency by 50%.
- Dynamic Precision Compensation System
- Temperature/Humidity Sensors: Embedded high-precision sensors (±0.5% RH/±0.1℃) for real-time environmental monitoring.
- AI Compensation Algorithm: Maintains stable 0.1-class accuracy (IEC 60044-2024 Class 0.1) across all operating conditions.
- Anti-Ferroresonance Magnetic Circuit Design
- RFC Damping Circuit: Parallel nonlinear resistors (10kΩ~1MΩ adaptive adjustment) suppress resonant overvoltage.
- Zero-Sequence Flux Cancellation: Symmetric dual-magnetic circuit structure reduces harmonic distortion to <0.2%.
III. Performance Validation (IEC Standard Tests)
|
Test Item |
Traditional Solution |
This Solution |
Improvement |
|
Power Frequency Withstand |
95 kV (dry)/70 kV (wet) |
130 kV (dry)/115 kV (wet) |
+37% |
|
Pollution Flashover (E5 class) |
28 kV |
40 kV |
+43% |
|
Annual Failure Rate |
>1.5% |
0.2% |
↓87% |
|
Temp. Cycling Error |
±0.5% |
±0.1% |
5× higher precision |
IV. Technical Advantages Summary
- Extreme Condition Resilience:
- Certified for C5-M corrosion resistance (ISO 12944), withstands pH=2~12 chemical environments.
- Lifecycle Cost Optimization:
- Maintenance cycle extended to 10 years; O&M costs reduced by 60%.
- Smart Expansion Capability:
- Supports IEC 61850 communication interface for real-time data upload to smart grids.
V. Application Cases
- Coastal Wind Farm (avg. humidity 85%):
- After replacing 32 traditional AIS-VTs: zero annual flashover faults; metering error stabilized at Class 0.1.
- Chlor-Alkali Chemical Plant (chlorine corrosion):
- Zero insulation degradation after 18 months; bushing hydrophobicity maintained HA-grade (highest class).
Compliance Standards: IEC 60044-2024 / IEEE C57.13 / GB/T 20840.7-202X
07/19/2025
Recommended
Solution for Medium-Voltage Motor Control and Protection Using Vacuum Contactor-Fuse (VCF) in a Coal Conveying System
Project BackgroundA coal conveying system comprises 15 belt conveyors driven by medium-voltage motors. The system operates under complex conditions, with motors often subjected to heavy loads and frequent starts. To address these challenges and achieve effective control and reliable protection during motor startup, the project comprehensively adopts Vacuum Contactor-Fuse (VCF) combination devices for the 6kV medium-voltage motor power distribution. This solution details the technical features,
ABB Vacuum Contactor KC2 Power Supply System Technical Transformation Plan
Issue OverviewThe 10kV air compressor starting system of a company utilizes the ABB vacuum contactor KC2 as the control component for the operating circuit. The dedicated wide-voltage power supply module paired with this contactor presents the following issues:Frequent failures: The power supply module fails to properly transition the voltage from 300V to 12V, resulting in fuse blowouts.Poor heat dissipation: Enclosed installation of the module leads to insufficient heat dissipation, acceler
Dedicated Vacuum Contactor Solution for Port Shore Power Systems
I. Background and ChallengesShore power systems have become core technical equipment for ports to reduce carbon emissions and noise pollution. However, these systems face two major challenges in the harsh operational environment of ports:Severe Environmental Corrosion: High humidity and salt spray in port areas cause serious corrosion to metal components and enclosures of electrical equipment, significantly impacting electrical lifespan and operational reliability.High Switching Requirements:
Vacuum Contactor Industrial Power Control Solutions
Application Background and Pain Point AnalysisIn modern industrial manufacturing power control systems, traditional contactors exhibit significant limitations under specific operating conditions:• Frequent Start-Stop Operations: Traditional contactors have limited mechanical lifespan, with frequent operations leading to coil burnout and mechanical jamming.• Poor Adaptability to Harsh Environments: Contacts are prone to oxidation in dusty environments, resulting in increased contact
About
Wone Store
Zhejiang Wone IT Service Co., Ltd..
2yrs +
staff 1000+m² US$300,000,000+ China
