HV610 sorozat speciális emelőfrekvenciafordító

Power input and output

Input voltage

380V(-15%)~480V(+10%) three-phase

Input power frequency

50Hz/60Hz ±5%

Input voltage imbalance

≤3%

Output voltage

0V~input voltage

Output frequency

0～600Hz

Mainly control performance

Motor type

Asynchronous motor, synchronous motor

Control mode

V/F, OLVC (Open-Loop Vector Control), CLVC (Closed-Loop Vector Control)

speed regulation range

1:10 V/F； 1:100 OLVC； 1:1000 CLVC

Start torque

OLVC：150%（0.5Hz）；CLVC：200%（0Hz）

Torque accuracy

≤±5%, under vector control mode

Torque pulsation

≤±5%, under vector control mode

Steady speed accuracy

OLVC： 0.2%； CLVC ：0.01%

Torque response

≤5ms, under vector control

acceleration and deceleration time

0.0s～3200.0s；0.0min～3200.0min

Torque increase

0.0％～30.0％

Overload capacity

150%1min/5min、180%10s/5min

VF curve

Straight type, multi-point type

Input frequency resolution

Digital setting 0.01Hz; Analog setting: Maximum frequency ×0.025%

Dedicated features

Anti-shake function

Prevents accidents caused by large swings of the load during acceleration or deceleration

Anti-loose rope protection

Accelerate slowly and rise smoothly according to whether the weight is lifted

Hook protection

After holding the gate, it detects whether the heavy object is hooked, and an alarm is issued, and the motor hovers

Holding the brake control

Control the brake holding device and loosening the brake through the judgment of frequency, current, etc., to avoid accidents such as slipping

Joystick zeroing detection

Determine whether the joystick is in neutral or not

Command reverse control

When the brake control is effective, it supports holding the brake to stop during the forward and reverse switching process, or running directly to the reversal frequency without holding the brake

Accelerate and deceleration switching

Support 3 frequency switching points to switch acceleration and deceleration time

Deceleration limit

Realize simple positioning function, automatic optimization of deceleration time

Voltage suppression

Automatically change the frequency to stabilize the bus voltage to prevent fault reporting

Overload protection

Prevents excessive loads from damaging the equipment

Low-speed operation protection

The main application is not suitable for machines that run at low speed for a long time

Load as you go

Automatically adjust the operating speed according to load changes to improve work efficiency

Macro parameters

According to the on-site application scenario, different lifting mechanisms choose different lifting macros

Basic features:

acceleration and deceleration curves

Straight line, S-curve

Simple PLC, multi-terminal speed

16 speed operation is achieved through the control terminal

Master-slave control

It can realize the master-slave synchronous control function of two or more motors

Automatic voltage adjustment

When the grid voltage changes within a certain range, it can automatically keep the output voltage constant

Multi-motor switching

Four sets of motor parameters, which can realize the switching control of four motors

Overvoltage and overcurrent stall control

Automatic current and voltage limit during operation to prevent frequent overcurrent and overvoltage tripping

Power outage and restart

After the frequency converter is powered off, when it is powered on again, it will automatically run after the set time is reached

Fast current throttling

Avoid frequent overcurrent failures of the frequency converter

Power input and output

Frequency setting method

Operation panel given, UP/DOWN terminal, multi-speed give, terminal pulse given, communication

Analog input terminals

AI1、AI2：0V～10V/ 0 (4)mA～20mA

Digital input terminals

DI1-DI5, 5 programmable digital inputs, optocoupler-isolated, drain/source compatible inputs

The DI5 supports high-speed pulse input with a maximum input frequency of 100kHz

Digital output terminals

open-circuit collector output; Output Voltage Range: 0V~24V; Current load capacity: 50mA

DO1 supports high-speed pulse output, maximum output frequency: 100kHz

Analog output terminals

1 way 0V~10V/0(4)mA~20mA

Relay output

1 contact type: FormC normally open + normally closed

communication

Communication protocol

Modbus RTU (standard); Profibus-DP, Profinet IO, CANopen, Modbus TCP/IP, Ethercat, EtherNet/IP (optional)

Usage environment

altitude

no derating is required within 1000 meters above sea level; At an altitude of 1000 meters ~ 3000 meters, the current must be reduced by 1% for every 100 meters of elevation

Ambient temperature

-25°C~+40°C (40°C to 55°C derating is allowed)

humidity

15%~95%, no condensation

vibration

0.75~110kW is the 3M3 standard, 2Hz&le;f<9Hz, displacement 1.5mm, 9Hz&le;f<200Hz, acceleration 5m/s2

132kW~400kW is the 3M5 standard, 2Hz&le;f<9Hz, displacement 3mm, 9Hz&le;f<200Hz, acceleration 10m/s2

Storage temperature

&minus;40&deg;C～+70&deg;C

Place of use

Indoors, there is no direct sunlight, no flammable and corrosive gases, liquids and conductive particles

Options:

code disk card, communication expansion card, I/O terminal expansion card

Protection function

Short circuit, overcurrent, overload, overvoltage, undervoltage, phase loss, overheating, external faults, etc

Installation method:

Loading machines and containers

Protection level

IP20

Cooling method

Air cooling